We all had a car which was affected at one point by small accidents such as scratches, paint jumping or clogging of the body. These are quite minor problems since they can be repaired quite easily.
The car paint has a layer of varnish on top which is activated and strengthened by the use of various chemicals. Below we present the way to repair deep scratches or spray paint in three different ways.
There are 3 categories of scratches depending on their depth - deep scratches, small scratches or surface scratches. Each of these types of scratches has a specific solution.
Use paint to repair deep scratches on the body
{{{ad-code}}}
Deep scratches will tend to worsen and worsen if you use an improper method of repairing them. Here are six simple steps you can take to repair this type of scratch.
1. Wash and dry the car carefully
This step involves careful cleaning of the car to remove any residue or dirt. You must pay special attention to the area that has the scratch and that you are going to repair.
Cleaning of this area must be done with great care so that it is finally extremely clean. Use microfiber cloths to wipe and dry the car.
2. Sand the damaged area
The purpose of this step is to remove the superficial layers of paint. Use 2000 sandpaper to prepare the scratched area for 10-15 seconds. After , check if you need to continue doing it to reach the deepest area of the scratch.
{{{ad-code}}}
It is especially important to consider the direction in which you use sandpaper. You can rinse the prepared surface with water to assess the situation.
Use 150 grit sandpaper if the scratch is a little deeper than the car’s varnish layer. Make sure there are no traces of debris stuck between the sandpaper and the car, as there is a danger that they will scratch the paint.
3. Rinse and dry the area. Dry the car with a microfiber cloth
After washing the car, use a clean microfiber cloth to wipe and dry the prepared surface. Be careful to use a clean cloth because using a dirty cloth can lead to scratching of the paint.
4. Apply a few coats of primer to the affected area
Apply a few coats of primer using back and forth movements. Wait about 5-10 minutes for it to dry.
Apply a new coat of primer after this interval. If possible, try to choose a primer that is the same color or is close to the color of your vehicle.
5. Apply a few coats of paint to the color of your car
Apply these coats of paint to the area where you previously applied the primer. Wait about 5-10 minutes between applications to allow the paint to dry completely.
{{{ad-code}}}
6. Applying wax to the repaired surface
After applying a few coats of paint, it is advisable to apply wax to the surface to waterproof the paint. Use a microfiber cloth to apply to the car surface.
You can also buy such a kit from any car store or on the internet, a kit that will include all the tools you will need to apply wax.
When doing this, it is good to apply a little pressure to the surface and use circular movements. Apply the wax until you notice that the surface becomes shiny.
How to remove small scratches by using a product to remove scratches?
According to specialists in the field, the use of such a product is the ideal solution when we want to remove small scratches from the body.
1. Washing the car
{{{ad-code}}}
Before starting the actual scratch removal process, you should clean the car to make sure there are no residues from these scratches. Carefully clean the affected area before applying any type of product because any residue at this level can cause new scratches.
Use car shampoo and microfiber cloths or special sponges to clean the car. Then dry the body surface using microfiber cloths to prepare the car for the next step.
2. Purchase a scratch removal product
Such a product can be purchased as a kit from specialty stores. This kit usually includes a solution but also a sponge for applying the product.
3. Apply the recommended amounts to the sponge
The quantity that will be used depends a lot on the manufacturer’s recommendation, but also on the scratched area. Apply the solution to the sponge and clean the affected area.
4. Applying the solution to the area damaged by scratches
Use circular motions to make sure the solution penetrates the affected area. Mainly, the movement that is most at hand can ensure the best preparation of the affected area.
Instead, be careful not to change direction. Do not change the movements when applying the product. Make sure that the product is evenly distributed on the surface you are working on.
{{{ad-code}}}
5. Rinse the solution
After finishing the application, it is advisable to clean the area of any remaining solution left on the body. Use microfiber cloths to remove any excess. Do not allow the solution to dry on the machine.
6. Repeat the procedure two or three times if necessary
If you notice that the scratches are still visible you can repeat the above two or three times. Do not repeat this process too many times because you can destroy the protective varnish of the paint.
Repairing scratches with toothpaste
Surface scratch repairs are the simplest repairs that can be made to a car. Use a tube of toothpaste to repair these scratches.
{{{ad-code}}}
1. Assess the condition of the scratches
First of all you should check if the scratches are on the surface or not with the help of your nail. To do this check, nail the scratched area or where the paint is sprayed.
If the nail sticks at this level it means that the scratch is not a surface one. Otherwise, using toothpaste to repair a superficial scratch may be the right choice.
2. Cleaning the scratched area
Before applying toothpaste on the scratched area, you must clean the area very carefully and then dry it. The area must be extremely clean to prevent additional scratching of the car’s paint. You can choose to take the car to a car wash or clean your car at home.
If you choose to wash your car at home you should use a hose to clean the entire car. Then apply the solution with car shampoo with a brush for cleaning cars or with a large sponge.
Apply the washing solution to the entire surface. Rinse and then wipe the entire surface of the machine using clean towels or microfiber cloths.
3. Apply toothpaste on a microfiber cloth
{{{ad-code}}}
It would seem that whitening toothpaste has a better effect than other types of toothpaste to remove scratches.
If you do not have such a toothpaste, you can use any toothpaste you have at hand. Apply a sufficient amount on a clean microfiber cloth.
4. Apply toothpaste to the affected area using circular motions
Make circular motions to remove superficial scratches. Continue these movements using medium pressure.
5. Rinse excess toothpaste
When you have finished removing the scratches, use a hose to rinse the substance off the body. Then use a microfiber cloth to wipe the area.
6. Repeat the whole process twice
Applying toothpaste once may not have the expected effects. In this case it is recommended to repeat the process once or twice more if necessary.
Then check the area to see if the scratches are still visible. Do not repeat this process more than three times because there is a risk of destroying the protective varnish of the paint.
{{{ad-code}}}
Photo source: quora.com, autoguru.com.au, gopaintsprayer.com, thevehiclelab.com, bestconsumerreviews.com, britishleylandautocenter.com, goauto.ca, diytips.com